A 5A power solution, 28 slots powered by four high-quality DC-DC converters.
ON/OFF 4HP – 3U module with 2 USB-A charging ports and a Power Button.

Friendly Plug and Play, tools are not required.

Features:

• 25 mm height over regulators grid and 15 mm height on the rest of the bus
• Horizontal connectors to maximize space
• 2,5mm barrel power connector
• On/Off 4HP module
• 2 USB-A charging ports

Specs:

• Power brick: 135W 2.5mm Barrel connector center positive (included)
• Current: +12V: 5A, -12V: 2,5A, 5V: 4A
• Measurements: 423 mm x 80mm
• Designed, kits prepared and completed modules assembled in Barcelona

Manufacturer Product Page HERE
Manufacturer Product Manual HERE

The post Befaco Trolley Bus Power Board and Module appeared first on Elevator Sound.

This is an ideal bus board for all Konstant Lab power supplies but also works with other eurorack power supplies as well. Bus board contains 19 output headers. 13 direct headers with decoupling capacitors and 6 filtered headers with unique filtering circuits. Filtered headers are specially dedicated to feed analog modules that are sensitive/susceptible to power quality.

Decoupling capacitors and LC filters reject noise caused by PSU and digital modules by 70%. Two 4 ways DIP switches can tune filtration capacity when some PSU has starting problems with big capacity on output – especially handy if you have a lot of digital modules present in your system.
Each power rail is protected against over-voltage for your modules and systems safety.

Technical:

• 39.3cm x 3cm
• 20 mm height with inserted connectors
• Two shock resistant “Push to Connect” input terminals
• 13 Direct Headers
• 6 Filtered Headers
• 19 TotaL shredded Output Headers
• Max Current- 4000m/a for whole busboard / 2000m/a for Filtered Section

The post Konstant Lab Filtered Bus Power Distribution Board appeared first on Elevator Sound.

Each Knurlie comes with a fitted plastic washer to prevent rack rash.

The post Befaco Knurlies Eurorack Screw (M3 – 50 Pack) appeared first on Elevator Sound.

They come with sixteen screws and special washers that help hold the screw in place during assembly and keep a tiny gap between the brackets and the Mantis.
Installation is fairly simple and takes about 30 minutes to complete.

Mantis Cases not included…

The post Tiptop Audio Mantis Case Dual Joiner Bracket (Black) appeared first on Elevator Sound.

They come with sixteen screws and special washers that help hold the screw in place during assembly and keep a tiny gap between the brackets and the Mantis.
Installation is fairly simple and takes about 30 minutes to complete.

Mantis Cases not included…

The post Tiptop Audio Mantis Case Dual Joiner Bracket (White) appeared first on Elevator Sound.

Each Knurlie comes with a fitted plastic washer to prevent rack rash.

The post Befaco Knurlies Eurorack Screw (M3 – 100 Pack) appeared first on Elevator Sound.

FC313 should fit any 3U Eurorack case and will locally add 3 1U rows, making the modules usable in their original orientation, unlike what is possible with commonly available 1U to 3U adapters.

The frame is held by 4 screws in the corners, making the top and bottom modules using the original rack rails, and the integrated rails allow combining multiple 1U modules on a single row.

Please Note the HP size in the product name is for the 1U rows, and the frame eats 2 more HP.

Manufacturer product page here.

The post XODES FC313 1U to 3U Adapter 6HP (Intellijel) appeared first on Elevator Sound.

FC313 should fit any 3U Eurorack case and will locally add 3 1U rows, making the modules usable in their original orientation, unlike what is possible with commonly available 1U to 3U adapters.

The frame is held by 4 screws in the corners, making the top and bottom modules using the original rack rails, and the integrated rails allow combining multiple 1U modules on a single row.

Please Note the HP size in the product name is for the 1U rows, and the frame eats 2 more HP.

Manufacturer product page here.

The post XODES FC313 1U to 3U Adapter 10HP (Intellijel) appeared first on Elevator Sound.

FC313 should fit any 3U Eurorack case and will locally add 3 1U rows, making the modules usable in their original orientation, unlike what is possible with commonly available 1U to 3U adapters.

The frame is held by 4 screws in the corners, making the top and bottom modules using the original rack rails, and the integrated rails allow combining multiple 1U modules on a single row.

Please Note the HP size in the product name is for the 1U rows, and the frame eats 2 more HP.

Manufacturer product page here.

The post XODES FC313 1U to 3U Adapter 12HP (Intellijel) appeared first on Elevator Sound.

FC313 should fit any 3U Eurorack case and will locally add 3 1U rows, making the modules usable in their original orientation, unlike what is possible with commonly available 1U to 3U adapters.

The frame is held by 4 screws in the corners, making the top and bottom modules using the original rack rails, and the integrated rails allow combining multiple 1U modules on a single row.

Please Note the HP size in the product name is for the 1U rows, and the frame eats 2 more HP.

Manufacturer product page here.

The post XODES FC313 1U to 3U Adapter 28HP (Intellijel) appeared first on Elevator Sound.